Deler Traxxas

9559 - Boots, Driveshaft (2)/ Retainer (Assembled) (2) Replacement part for these models: Sledge®

9587 -  Drive Cup, Front or Rear for Traxxas Sledge (2) Drive cup, front or rear (hardened steel) (for differential pinion gear)/ driveshaft boots (2)/ boot retainers (2)

9651 - Spur Gear,  Sledge 46-tooth, Steel (1.0 metric pitch) 46-tooth steel spur gear (1.0 metric pitch) fits Sledge® center differential. Traxxas spur gears let you fine-tune the performance of your Traxxas model. Changing gear ratios can help balance acceleration and top speed for different running conditions. Please consult your owner’s manual for more information on recommended gearing options for your specific model. Accessory part for these models: Sledge®

9950 - Official Team Traxxas® Racing Dekal Set Official Team Traxxas® racing decal set (flag logo/ 6-color) The official Team Traxxas Racing Decal sheet has been revised and now includes EZ-Start®, Stinger Motors, ProGraphix, TRX® Engines and www.Traxxas.com logos. Perfect for adding that “final touch” to your Traxxas ProGraphix® painted body, or your own personal painting schemes. Replacement part for these models: 1/16 E-Revo® VXL 1/16 E-Revo® 1/16 Slash 4WD 1/16 Summit VXL 1/16 Summit Maxx® X-Maxx® Accessory part for these models: 4-Tec® 2.0 AWD Chassis 4-Tec® 2.0 VXL AWD Chassis Blast E-Revo® VXL Brushless Ford F-150 Raptor Ford Fiesta® ST Rally Revo Rustler® 4X4 VXL Rustler® 4X4 Rustler® VXL Rustler® Slash 2WD Unassembled Kit Slash 4X4 Platinum Slash 4X4 Ultimate Slash 4X4 VXL Slash 4X4 Slash VXL Slash Slayer Pro 4X4 Stampede® 4X4 Unassembled Kit Stampede® 4X4 VXL Stampede® 4X4 Stampede® VXL Stampede® TRX-4® 1979 Chevrolet Blazer TRX-4® Equipped with Traxx™ TRX-4® Ford Bronco TRX-4® Mercedes-Benz® G 500® 4X4² TRX-4® Scale and Trail™ Crawler TRX-4® Sport Unassembled Kit TRX-4® Sport TRX-4® Unassembled Kit TRX-6™ Mercedes-Benz® G 63® AMG 6X6 Unlimited Desert Racer® XO-1® Bandit Bigfoot® No. 1 Officially Licensed Replica Bigfoot® Officially Licensed Replica E-Revo® VXL Brushless Jato Nitro Rustler Nitro Slash Rustler® 4X4 Rustler® Slash Stampede® 4X4 Unassembled Kit Stampede® 4X4 VXL Stampede® 4X4 Stampede® VXL Stampede® Summit T-Maxx TRX-4® 1979 Chevrolet Blazer TRX-4® Equipped with Traxx™ TRX-4® Ford Bronco TRX-4® Mercedes-Benz® G 500® 4X4² TRX-4® Scale and Trail™ Crawler TRX-4® Sport Unassembled Kit TRX-4® Sport TRX-4® Unassembled Kit TRX-6™ Mercedes-Benz® G 63® AMG 6X6

Adapter for Traxxas iD - Parallellkobling 2 x Hann - 1 x Hunn Adapter for å parallellkoble to batteripakker med Traxxaskontakter. Original Traxxas iD kontakter er bakoverkompatibel med eldre TRX kontakter. Kun Traxxas Y-harnesser lar deg bruke dobbel batteristrøm for økt hastighet eller driftstid, med den dokumenterte bekvemmeligheten og ytelsen til ekte Traxxas High-Current Connectors. Velg parallellkabelen for å kombinere batterikapasiteten for ekstra lang driftstid. Dobbel batteridrift krever at man følger forholdsreglene som er angitt i modellens bruksanvisning. Følg alle forholdsregler for å sikre topp ytelse og pålitelighet for modellen og batteriene dine. Traxxas parallelle og serie Y-kabler er kun for bruk med 2/3A batteripakker. Kun for bruk med 7,2 V NiMH-batteripakker

Crawler/Car Stand Laserskjært MDF Kit De 10 første er nummerert Limited Edition med TRX4 eller Axial logo inkludert: (Verdi 150,-) Lokalt produsert Car Stand for Crawler, laserskjært i 3mm mdf, leveres i kit for selv montering, kan med fordel males. Kan leveres i hjulbase 312mm og 324mm, velg i varianter.  Bilder for illustrasjon :  

Dekk og Felg MT Pioneer Maxx Soft Sort 17mm (2) LOUISE LT3329SB - MT-PIONEER Tires with MFT for Traxxas MAXX This is the new Louise Monster Truck tires for the Traxxas Maxx with 17mm hexes (also fits some other buggies/trucks with 17mm hexes). They are equipped with MFT technology that has a soft rubber compound for optimal grip but still limits the amount of tire expansion due to the built-in MFT cord. Note that these also have an built-in extra off-set for added stability, that gives the awesome Maxx truck a wider stance (roughly +20 mm) so you can drive it even harder. The MT-PIONEER tire tread is perfect for most loose to rough surfaces and general bashing. Specs: Fits: Traxxas MAXX (and other trucks with 17mm hex) Diameter: 136.9mm Width: 70.2mm Hex: 17 mm Bead-Lock Rim Color: Black Wheel Off-set: +1/2" Tire Compound: Soft Tire Technology: MFT (limits ballooning/tire expansion)

Dekk og Felg MT Uphill Maxx Soft Sort 17mm (2) LOUISE LT3330SB - MT-UPHILL Tires with MFT for Traxxas MAXX This is the new Louise Monster Truck tires for the Traxxas Maxx with 17mm hexes (also fits some other buggies/trucks with 17mm hexes). They are equipped with MFT technology that has a soft rubber compound for optimal grip but still limits the amount of tire expansion due to the built-in MFT cord. Note that these also have an built-in extra off-set for added stability, that gives the awesome Maxx truck a wider stance (roughly +20 mm) so you can drive it even harder. The MT-UPHILL tire tread is perfect for most loose to rough surfaces and general bashing. Specs: Fits: Traxxas Maxx (and other trucks with 17mm hex) Diameter: 136.4mm Width: 70.2mm Hex: 17 mm Bead-Lock Rim Color: Black Wheel Off-set: +1/2” Tire Compound: Soft Tire Technology: MFT (limits ballooning/tire expansion)

Dusty Motors Protection Cover Granite/Stampede/Hoss 4x4 Dusty Motors beskyttelsestrekk for Arrma Granite, Stampede, Telluride, Rustler, Hoss  4x4 og like biler i skala 1/10 Beskyttelsestrekket er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. festes med borrelås i chassiset på bilen. Video This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If its hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When its hot outside or if you have a car gearing set up thats capable of reaching the speed of light be smart when you bash. Dont let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, dont bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they cant be breathable and 100 percent waterproof at the same time. Physics just doesnt work that way. The splashes of water are OK, so dont be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

Dusty Motors Protection Cover TRX0031 for Slash 4x4 Støv og grusbeskytter med glidelås for enkel tilgang til skift av batteri o.l, festes i chassis sidene med borrelås. Dusty Motors beskyttelsestrekk for Slash 4x4 (IKKE LCG) og like biler i skala 1/10. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken.

Dusty Motors Protection Cover TRX0051 for Slash 4x4 LCG Støv og grusbeskytter med glidelås for enkel tilgang til skift av batteri o.l, festes i chassis sidene med borrelås. Dusty Motors beskyttelsestrekk for Slash 4x4 og like biler i skala 1/10. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken.

Dusty Motors TRX0101 Protection Cover for X-Maxx Dusty Motors beskyttelsestrekk i svart for Traxxas X-Maxx.  Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If it?s hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When it?s hot outside ? or if you have a car gearing set up that?s capable of reaching the speed of light ? be smart when you bash. Don?t let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, don?t bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they can?t be breathable and 100 percent waterproof at the same time. Physics just doesn?t work that way. The splashes of water are OK, so don?t be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

Dusty Motors TRX0131 Protection Cover for Maxx Dusty Motors beskyttelsestrekk i svart for Traxxas Maxx. Beskyttelsestrekk til demperne følger ikke med. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If it?s hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When it?s hot outside ? or if you have a car gearing set up that?s capable of reaching the speed of light ? be smart when you bash. Don?t let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, don?t bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they can?t be breathable and 100 percent waterproof at the same time. Physics just doesn?t work that way. The splashes of water are OK, so don?t be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

Dusty Motors TRX0191 Protection Cover for Wide-Maxx Dusty Motors beskyttelsestrekk i svart for Traxxas WideMaxx. Beskyttelsestrekk til demperne følger ikke med. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If it?s hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When it?s hot outside ? or if you have a car gearing set up that?s capable of reaching the speed of light ? be smart when you bash. Don?t let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, don?t bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they can?t be breathable and 100 percent waterproof at the same time. Physics just doesn?t work that way. The splashes of water are OK, so don?t be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

INJORA 43g Brass Axle Mount Set Suspension Links Stand for TRX-4 INJORA Brass Axle Mount Set Suspension Links Stand for RC Crawler Car Traxxas TRX-4 Suit For: 1/10 RC Crawler Traxxas TRX-4 Features: Made of high quality metal CNC crafts, high precision and durability Replace the TRX4 original plastic parts 8227 Specification: Material: Brass Quantity: 4pcs Weight: 43g

Lexan Karosseri for Rustler 4x4 Lakkert og Montert (Komplett) 1/10 Tilpasset og klippet lakkert lexankarosseri for 1/10 Stadiumtruck. Leveres med vindumaskering og dekaler. Lengde: 430mm Bredde: 140mm Hjulbase: ca 290mm Accessory part for these models: Rustler® 4X4 VXL Rustler® 4X4

Messing Portalcover 42g F/R for Traxxas TRX-4 (2) 1 sett portalcover for 1 aksel totalt 84gram, kan brukes både foran og bak.   Description: Get more from your tires with this Brass made portal cover by adding weight exerted onto your tires when compared to the stock plastic items! Easy to remember with etched weight on the face of the cover.     *Photos for reference only.   Feature: For: Traxxas TRX-4 Material: Brass Color: Brass   Include: Brass Front or Rear Portal Cover (2 pcs)  PDF Datasheet   

Mutter - 2.5mm Låsemutter Nylock M2.5 (12) 12 stk Traxxas 2.5mm låsemutter

6735 - Traxxas Front Bumper/Skid Plate Black   Støtfanger foran til Stampede/Telluride/Hoss 4x4 Replacement part for these models: Hoss™ 4X4 VXL Stampede® 4X4 Unassembled Kit Stampede® 4X4 VXL Stampede® 4X4

TRX4-004BK - Servo Horn Aluminium for Styring 25T/23T TRX-4-6 Smart servohorn for 2 typer servo splines, dette har 25T splines på den ene siden og på 23T splines på andre siden. Hornet kan også brukes på andre typer produkter med slike servoer. Yeah Racing Aluminum 23T 25T Servo Horn Black For Traxxas TRX-4 TRX-6 Description: Symmetrical axis servo horn, allows this servo horn to have both 23t and 25t servo splines so you can keep less parts! Keeps the same geometry as the stock servo horn as found on the TRX-4! Features a silver edge finish to give your chassis that bling look! A securing hole on the side to make sure this servo horn stays on your servo. Made from Aluminum to allows it to be strong enough to deal with the torque generated by brushless servos! Feature: For: Traxxas TRX-4 and Futaba/Sanwa Servos Color: Black Material: Aluminum Include: Aluminum 23T 25T Servo Horn (1 pc) Screws (2 pcs)  

TRX4-007BK - Aluminium Rear Damper Mount For Traxxas TRX-4 Støtdemperfester i aluminium bak for TRX4 Description: Aluminum damper mount for Traxxas's TRX-4. Increase the overall strength of your chassis with this aluminum upgrade part! *Photos for reference only. Feature: For: Traxxas TRX-4 Material: Aluminum Color: Black Include: Aluminium Rear Damper Mounts (2 pcs) Screws (1 pack)

TRX4-011BK - Aluminum Front & Rear Suspension Link Mount Set For Traxxas TRX-4 'G6 Certified' Description: Increase the durability of your Traxxas TRX-4 with these aluminum link mount set! The front pan hard bar mount is integrated into one of the mounts and increase stiffness of the front end. *Photos for reference only. Feature: For: Traxxas TRX-4 Material: Aluminum Color: Black Include: Aluminum Link Mounts (4 pcs)    

TRX4-014BK - Aluminum Motor Mount Black For Traxxas TRX-4-6 Black 'G6 Certified' Aluminiums motorfeste for TRX4-6, sterkere enn plastoriginalen og lader varme bedre vekk fra motor. Description: This Aluminum motor mount plate is a direct upgrade for the standard plastic part, this part is stronger and will help with keeping your motor cool due to it being made of aluminum. Feature: For: Traxxas TRX-4 Material: Aluminum Color: Black Include: Aluminum Motor Mount (1 pc)

TRX4-065 - Alloy Low Battery Plate for Traxxas TRX-4-6 Lavtbyggende batterifeste for TRX-4-6 crawlere Lavt tyngdepunkt batteri kasse for Traxxas TRX-4-6, ved å sette batteriet lavere får du et lavere tyngdepunkt som hjelper bilen din til å takle hellinger bedre og reduserer sjansen for at den velter! Batterilfestet er endret til å bruke borrelås og med de integrerte stroppene holder alle slags størrelser på 2-3s batterier på plass uansett tykkelse! *Photos for reference only. Feature: For: Traxxas TRX-4 Material: Alloy Color: Black Battery Size : 130mm X 43mm (Max) Include: Battery Tray (1 pc) Battery Brace (1 pc) Velcro Strap (1 pc) Screws (8 pcs)(2pcs of 14mm for 312mm wheelbase)

TRX4-070 - Stainless Steel Steering & Suspension Link Set For Traxxas TRX-4 Styrelink og Panhardstag i rustfritt stål(plastlinker) Description: Stainless steel steering and suspension linkage set for your Traxxas TRX-4, made from stainless steel allows you to crawl in water without worrying! Feature: For: Traxxas TRX-4 Material: Steel Color: Silver Include: Linkages (3 pcs)

TRX4-075 - Rear Metal Bumper For Traxxas TRX-4 TRX4-6 Kraftig svart bakfanger til Traxxas TRX-4 og TRX-6 med Mercedes G500 G63-karosseriet. Ikke kompatibel med originalfangeren. Yeah Racing Rear Metal Bumper For Traxxas TRX-4 TRX4-6 Description: High detail scale rear bumper for Traxxas's TRX-4 and TRX-6! Protects your chassis from rocks and other obstacles on the trail! *Photos for reference only. Feature: For: Traxxas TRX-4 TRX4-6 (Benz G500 G63 Body) (Not compatible with stock fender) Material: Metal Color: Black Include: Rear Metal Bumper (1 pc) Bumper Brace (1 pc) Screws (4 pcs)  

TRX4-S01 - Messing Oppgradering V2 for Traxxas TRX-4-6  (2) Brass Upgrade Parts Set For Traxxas TRX-4 G6 certified med nytt svingarm/portalhus for mere solid overføring til styrestag. Messingoppgradering for TRX4 og TRX6 foran, her får du ca 328gr ekstra vekt på framaksel. Description: Brass upgrade combo for your Traxxas TRX-4, upgrade to these parts to get more grip out of your tires! Brass also means sturdier than the original plastic parts. Comes with all required mounting hardware required to install this combo onto your truck!       *Photos for reference only.   Feature: For: Traxxas TRX-4 Material: Brass Color: Brass   Include: Brass Steering Knuckles V2 (2 pcs) Brass C Hubs (2 pcs) Brass Hexes (4 pcs) Brass Portal Covers (2 pcs) Mounting Hardware (1 pack)     PDF Datasheet   

WideMaxx X-Maxx Bredde Sett Sett med det du trenger for å øke bredden på X-Maxx. X-Maxx WideMaxx-settet inkluderer bredere kraftige bærearmer for en 2,36" (60 mm) økning av bredde. Støpt i TRAXXAS sitt tøffeste komposittmateriale, tilbyr de nye armene akkurat nok flex til å motstå brudd, selv i kaldt vær. Fem forskjellige fargealternativer gir maksimal tilpasning av din X-Maxx. Nye 1.346 sjokkfjærer erstatter standardfjærene for optimal håndtering. Bredere fjæringslenker og drivaksler i stål fullfører pakken, og X-Maxxs gjennomtenkte konstruksjon gjør installasjonen rask og enkel. A Tougher, Wider Stance The Traxxas X-Maxx is a new breed of monster truck with a tough-as-nails attitude, brutal power, and unrivaled durability. The WideMaxx kit builds on the X-Maxx’s already legendary performance by widening the stance 60 mm for even greater cornering stability. Take your X-Maxx to the next level with the WideMaxx kit and get ready for the ultimate expression of Traxxas Tough™. Over 2" Wider for Ultimate High-Speed Stability The WideMAXX kit includes widened versions of the extreme heavy-duty suspension arms, along with lengthened steel driveshafts and heavy-duty composite toe links. New 1.346 rate springs ensure optimum performance. A Tougher, Wider Stance The Traxxas X-Maxx® sets the standard for extreme monster truck fun with a tough-as-nails attitude, brutal power, and unrivaled durability. The WideMaxx® kit builds on the X-Maxx’s already legendary performance by widening the stance 60 mm for even greater cornering stability. Take your X-Maxx to the next level with the WideMaxx kit and get ready for the ultimate expression of Traxxas Tough™. Features: Available in five different color options (Black, Green, Red, Orange, Blue) Widens the X-Maxx by 60 mm for increased cornering stability Widened Extreme Heavy-Duty Suspension Arms Kit Includes: Upper suspension arms (4) Lower suspension arms (4) Lengthened steel driveshafts (4) WideMAXX heavy-duty composite toe links (2) New springs (1.346 rate)

Y-Kabel 80mm FUTABA/Universal 26AWG Y-kabel for paralellkobling av bl.a servoer, passer de fleste universalkontakter, er Futaba kontakt i begge ender så "leppen" må kuttes vekk ved bruk i bl.a Spektrummotakere, kabelen har ingen stor "koblingskloss" og passer godt der man har begrenset med plass og vil spare vekt.   Servo connector, Y adapter (for dual-servo steering)  

YA-0548 - Aluminum Alloy Front Bumper w/ LED Light For Axial SCX10 II Traxxas TRX-4 Dette er en ny maskinert støtfangere av aluminium for chassis montering for SCX10, SCX10 II og Traxxas TRX-4 fra Yeah Racing, denne beskytter chassiset når du tipper fremover når støtfangeren pekes utover. Dette produktet vil oppfylle ditt behov for stadig mer realistisk tilbehør med mer skalert tilbehør. Støtfangeren har monteringspunkter for vinsjer og doble slepepunkter med sjakler inkludert. Denne støtfangeren monteres på rammen, så den kan tilpasses til alle SCX10-chassis og TRX-4. Description: This is a new series of machined aluminum chassis mounted bumpers for SCX10, SCX10 II and Traxxas's TRX-4 from Yeah Racing, protect your chassis when you flip over as the bumper is pointed outwards. This product will fulfill your need for ever more realistic accessories with more scaled accessories. The Bumper features mounting points for winches and dual tow points with shackles included. This bumper mounts onto the frame, so it will for sure fit all SCX10 chassis's and TRX-4.     *Photos for reference only. Feature: For: Traxxas TRX-4 Defender / Bronco / Axial SCX10 / II HPI Venture/Gmade Bom Material: Aluminum Color: Black Include: Yeah Racing Alloy Front Bumper (1 pc) Shackles (2 pcs) LED Cable (1 pc) Mounting Hardware (1 pack) PDF Datasheet 

Yeah Racing Plastic Power Switch For Traxxas TRX-4 TRX-6 Ekstern bryterarm som gjør at du kan slå av og på bilen fra undersiden uten å måtte ta av karosseriet. Description: Hate taking off the body to switch your Traxxas esc on or off? Use this extension for the button for easy power up and down. The lever tucks neatly underneath the rock slider and will not come into contact with rocks for accidental power downs.   *Photos for reference only. Feature: For: Traxxas TRX-4 Material: Plastic Color: Black/Red Include: Switch Extension (1 pc) Mounting Tape (2 pcs) Mounting Hardware (1 pack)