RC-BILER OG DELER

Bronto Karosseriklips Stor Sølv (8) Karosseriklips egnet for medium store bilmodeller; 1:6, 1:7, 1:8. Bronto kvalitetsklips leveres i pakker på 8 stykk. Disse karosserikipsene har en diameter på 1.5 mm. Hver klips har en liten bøy ved hodet, slik at det er enklere å få tak de når de skal settes av/på. Lengde 34.0 mm Høyde 12.0 mm Diameter 1.5 mm Egnet skala* 1:6, 1:7, 1:8 * Egnet skala er kun en indikasjon. Ulike bilprodusenter kan ha lagt opp til å bruke andre mål. Benytt derfor millimetermålene for å være sikker på at du får klips som passer akkurat din modell.

Bronto Karosseriklips Medium Sort (8) Karosseriklips egnet for medium store bilmodeller; 1:6, 1:7, 1:8. Bronto kvalitetsklips leveres i pakker på 8 stykk. Disse karosserikipsene har en diameter på 1.5 mm. Hver klips har en liten bøy ved hodet, slik at det er enklere å få tak de når de skal settes av/på. Lengde 34.0 mm Høyde 12.0 mm Diameter 1.5 mm Egnet skala* 1:6, 1:7, 1:8 * Egnet skala er kun en indikasjon. Ulike bilprodusenter kan ha lagt opp til å bruke andre mål. Benytt derfor millimetermålene for å være sikker på at du får klips som passer akkurat din modell.

BSD - Clutch 2 Sko med fjær for Nitro motor (1)  2 sko clutch i metall for motorer med 2 sko. Passer mange modeller. Ø = 21.7mm Bredde = 7.8mm For svinghjuls pinne = 2.5mm

BSD 125mm Rett Lexan Karosseri Liten Saks   Rett saks for klipping av karosserier/Canopy o.l, Fin å bruke for å klippe rette linjer, er også utmerket til dekalklipping. Lengde : 125mm (44mm egg)

BSD 45-903-015 - Steering Arm Set L/R Styrearmsett for BSD 1/10 biler bruk manual for rett modell

BSD 45-903-017S - C-Carrier Screw Set and Bushes 4mm Skruesett med hylser for c-hub foran BSD 1/10 biler bruk manual for rett modell 4 stk 4x13mm Skruer 2 stk Hylser 4x6.1x5.1x6.1mm  (innvendig x høyde x utvendig x flens) 2 stk Hylser 4x4.7x5.1x6.1mm

BSD- 909-004M - Hard metall 32P 13T pinion for 3.17mm Aksel Denne brukes sammen med 45-MPO021M Hard metall pinjong til BSD sin Monster Truck Børste og Børste løs (909 & 706T) Og Buggy Børste og børsteløs. (701G & 701G-R) Dette er biler i scala 1:10 ill.foto

BSD- 909-005M - Hard metall 32P 11T pinion for 3.17mm Aksel Denne brukes sammen med 45-MPO021M Hard metall pinjong til BSD sin Monster Truck Børste og Børste løs (909 & 706T) Og Buggy Børste og børsteløs. (701G & 701G-R) Dette er biler i scala 1:10 ill.foto

BSD-45-MPO-021M - Hard metall 32P 51T SpurGear 701,701G,706T,909

BSD-701-019GM - Hard Metall 32P 15T pinion for 3.17mm Aksel Denne brukes sammen med 45-MPO021M Hard metall pinjong til BSD sin Monster Truck Børste og Børste løs (909 & 706T) Og Buggy Børste og børsteløs. (701G & 701G-R) Dette er biler i scala 1:10 ill.foto

BSD-809-012 - Servo Saver Link 2 stk Servostag med skruer for BSD biler, bl.a 809 1/8 buggy

BSD-903-098 - Diff.Gearbox BulkHead-Upper/Lower Utvendig differensialhus for BSD

BSD-910-002 - Brace Unit Støtdempertårn og karosseristolpe for BSD Ramasoon

BSD-MPO-011 - Steering Linkage Aluminium (1) Styrelink for BSD 701G Buggy (Børste), 701G-R Buggy, 706T Monster Truck (Børste), 801 Monster Truck, 803T Land Ripper, 808T Monster Truck, 809T Buggy, 908 Monster Truck, 909 Monster Truck Dette er lenkearmen mellom servo overføringene. Inkludert skruer,støttehylser og lager.

Clutch i Aluminium og Svinghjulsett for 3.5-5.2cc 3 sko Svinghjul og Clutch i lakkert aluminium som passer de fleste 3.5 til 5.2cc Nitromotorer, kan også brukes på racemotorer i mindre versjoner også. Komplett med svinghjul, kon, mutter, 3sko aluminiums clutch med fjærer.

CM-003  Decal Zone: Royal Air Force - 300x100mm Dekalark for RC modeller av høy kvalitet. Beregnet for bruk på flymodeller, men egner seg også på biler, båter og helikopter. Trykket er på transparent bakgrunn for best mulig resultat. Bredde 300mm Høyde 100mm

Crawler Luggage Tray with 4 Lights Takgrind/bagasjegrind for takmontering. Spenning: 4.8V – 6.0V Lengde Total: 156mm Dimensjon tray: 132x103x25mm Tray festes med 4x3mm mutter Takgrind med 4 led lys. Veldig bra lys på denne! Produsert i lakkert stål. En meget flott takgrind for din skalabil. Den egner seg i hovedsak for biler i scala 1:10 LED plugges rett i mottaker og egnet kontakt er påmontert. Eller kobles til eget batteri.

Crawler/Car Stand Laserskjært MDF Kit De 10 første er nummerert Limited Edition med TRX4 eller Axial logo inkludert: (Verdi 150,-) Lokalt produsert Car Stand for Crawler, laserskjært i 3mm mdf, leveres i kit for selv montering, kan med fordel males. Kan leveres i hjulbase 312mm og 324mm, velg i varianter.  Bilder for illustrasjon :  

dBoots'FORTRESS' Dekk Sett Limte Mojave GROM 2 par These high-quality dBoots FORTRESS tires, mounted on ARRMA wheels, are direct replacements for your kit items. Includes 4 x wheels with pre-glued dBoots FORTRESS tires Features Tires: Multi-surface 'FORTRESS' tread pattern for awesome traction in all conditions High-quality rubber for long-lasting durability Pre-glued for trouble-free fit and fast servicing Vent holes in tires allow air to move in and out of the tire to improve traction and soak-up bumps and landings Vent holes also allow water and dirt to escape from the tire to prevent unbalanced tires and increase durability Wheels: 12 spoke design for stylish looks and increased strength Tough nylon for durability on all surfaces 12mm hex for strength during extreme driving action and easy servicing

Dekk og Felg MT Pioneer Maxx Soft Sort 17mm (2) LOUISE LT3329SB - MT-PIONEER Tires with MFT for Traxxas MAXX This is the new Louise Monster Truck tires for the Traxxas Maxx with 17mm hexes (also fits some other buggies/trucks with 17mm hexes). They are equipped with MFT technology that has a soft rubber compound for optimal grip but still limits the amount of tire expansion due to the built-in MFT cord. Note that these also have an built-in extra off-set for added stability, that gives the awesome Maxx truck a wider stance (roughly +20 mm) so you can drive it even harder. The MT-PIONEER tire tread is perfect for most loose to rough surfaces and general bashing. Specs: Fits: Traxxas MAXX (and other trucks with 17mm hex) Diameter: 136.9mm Width: 70.2mm Hex: 17 mm Bead-Lock Rim Color: Black Wheel Off-set: +1/2" Tire Compound: Soft Tire Technology: MFT (limits ballooning/tire expansion)

Dekk og Felg MT Uphill Maxx Soft Sort 17mm (2) LOUISE LT3330SB - MT-UPHILL Tires with MFT for Traxxas MAXX This is the new Louise Monster Truck tires for the Traxxas Maxx with 17mm hexes (also fits some other buggies/trucks with 17mm hexes). They are equipped with MFT technology that has a soft rubber compound for optimal grip but still limits the amount of tire expansion due to the built-in MFT cord. Note that these also have an built-in extra off-set for added stability, that gives the awesome Maxx truck a wider stance (roughly +20 mm) so you can drive it even harder. The MT-UPHILL tire tread is perfect for most loose to rough surfaces and general bashing. Specs: Fits: Traxxas Maxx (and other trucks with 17mm hex) Diameter: 136.4mm Width: 70.2mm Hex: 17 mm Bead-Lock Rim Color: Black Wheel Off-set: +1/2” Tire Compound: Soft Tire Technology: MFT (limits ballooning/tire expansion)

Drevsett Girkasse + Spur 50T 32P Promoto MX (LOS262007)  

DSG-08A - Aluminum Shock Head Set For DSG Shocks Description: This is a set of four replacement Shock Gear Pillow Ball from Yeah Racing. This extremely tough Pillow Ball has been machined from a solid block of aluminum for incredible precision, rigidity and durability. This Pillow Ball is very suitable for upgrading your Shock Gear.       *Photos for reference only.   Feature: For: Shock-Gear Material: Aluminum Color: Black   Include: Aluminum Shock Head (4 pcs) M3 x 12mm Flat Head Screw (4 pcs) 4.8mm Ball (4 pcs) Manual (1 pc)   Manual:         PDF Datasheet   

DUBRO2235 - Silikon Fuelslange 2mm 60cm Lysblå SPECIFICATIONS Lengde: 609mm Inner Diameter: 2mm Silikonslange som kan brukes til de fleste formål. Our tubing is made from high quality silicone that is durable and will perform just the way it should. With no kinks when coiled and superb gripping on your fittings, Nitro Line is the real professionals choice. 50 foot spools also avail.

DUBRO340 - In-Line Fuel Filter w/Plug Medium Fuelfilter for både metanol og bensin. Delbart med 130mikron filter. for innvendig 3.0-4.5mm slange, total lengde 28.7mm   FEATURES Constructed of two threaded aluminum parts which separate for ease in cleaning. Includes a 130 micron mesh screen filter to filter out the smallest of particles and an O-ring to properly seal against leakage. Suitable for gasoline or glow fuel. Is installed in fuel tubing between the carburetor and fuel tank. Fits 2.5-3.5mm diameter tubing.     INCLUDES One Medium In-Line Fuel Filter.     REQUIREMENTS 2.5-3,5mm diameter fuel tubing.     SPECIFICATIONS Length: 1-1/8"

DUBRO341 - In-Line Fuel Filter w/Plug Large Scale Fuelfilter for både metanol og bensin. Delbart med 130mikron filter. for innvendig 3.5-4.5mm slange, total lengde 31.3mm   Constructed of two threaded aluminum parts which separate for ease in cleaning. Works for both gas and glo fuels. 130 micron mesh screen filter to filter out the smallest of particles and an o-ring for a positive, no-leak seal. Dimensions: 1.125" (28.575 mm) L X 7/16" (11.11 mm) W. #341 - The Large Scale In-Line Fuel Filter is made for bigger engines that require more fuel filtering capacity. Dimensions: 1.25" (28.575 mm) L X 9/16" (14.29 mm) W WORKS WITH GAS & GLO FUEL Use DU-BRO® Medium (3/32" ID) or Large (1/8" ID) Silicone (glo) or Tygon (gasoline) tubing. Weight: All except #341- 3 grams/each #341 - 5 grams/each Made in USA     INCLUDES One Medium In-Line Fuel Filter.     REQUIREMENTS 3.5-4,5mm diameter fuel tubing.  

Dunlop MX53 Bakhjul Chrome Promoto MX (1) Bakdekk med felg for Promoto MX

Dusty Motors ARM0011 Protection Cover for Kraton/Talion Dusty Motors beskyttelsestrekk i svart for Arrma Kraton og Talion (opp til 2018). Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If its hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When its hot outside or if you have a car gearing set up thats capable of reaching the speed of light be smart when you bash. Dont let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, dont bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they cant be breathable and 100 percent waterproof at the same time. Physics just doesnt work that way. The splashes of water are OK, so dont be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer. https://youtu.be/qNNSt-XJa98

Dusty Motors ARM0031 Protection Cover for Senton 3/6S Dusty Motors beskyttelsestrekk i svart for Arrma Senton 3-6S. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If its hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When its hot outside or if you have a car gearing set up thats capable of reaching the speed of light be smart when you bash. Dont let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, dont bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they cant be breathable and 100 percent waterproof at the same time. Physics just doesnt work that way. The splashes of water are OK, so dont be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer. https://youtu.be/qNNSt-XJa98

Dusty Motors Protection Cover Granite/Stampede/Hoss 4x4 Dusty Motors beskyttelsestrekk for Arrma Granite, Stampede, Telluride, Rustler, Hoss  4x4 og like biler i skala 1/10 Beskyttelsestrekket er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. festes med borrelås i chassiset på bilen. Video This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If its hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When its hot outside or if you have a car gearing set up thats capable of reaching the speed of light be smart when you bash. Dont let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, dont bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they cant be breathable and 100 percent waterproof at the same time. Physics just doesnt work that way. The splashes of water are OK, so dont be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

Dusty Motors Protection Cover TRX0031 for Slash 4x4 Støv og grusbeskytter med glidelås for enkel tilgang til skift av batteri o.l, festes i chassis sidene med borrelås. Dusty Motors beskyttelsestrekk for Slash 4x4 (IKKE LCG) og like biler i skala 1/10. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken.

Dusty Motors Protection Cover TRX0051 for Slash 4x4 LCG Støv og grusbeskytter med glidelås for enkel tilgang til skift av batteri o.l, festes i chassis sidene med borrelås. Dusty Motors beskyttelsestrekk for Slash 4x4 og like biler i skala 1/10. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken.

Dusty Motors TRX0101 Protection Cover for X-Maxx Dusty Motors beskyttelsestrekk i svart for Traxxas X-Maxx.  Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If it?s hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When it?s hot outside ? or if you have a car gearing set up that?s capable of reaching the speed of light ? be smart when you bash. Don?t let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, don?t bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they can?t be breathable and 100 percent waterproof at the same time. Physics just doesn?t work that way. The splashes of water are OK, so don?t be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

Dusty Motors TRX0131 Protection Cover for Maxx Dusty Motors beskyttelsestrekk i svart for Traxxas Maxx. Beskyttelsestrekk til demperne følger ikke med. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If it?s hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When it?s hot outside ? or if you have a car gearing set up that?s capable of reaching the speed of light ? be smart when you bash. Don?t let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, don?t bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they can?t be breathable and 100 percent waterproof at the same time. Physics just doesn?t work that way. The splashes of water are OK, so don?t be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

Dusty Motors TRX0191 Protection Cover for Wide-Maxx Dusty Motors beskyttelsestrekk i svart for Traxxas WideMaxx. Beskyttelsestrekk til demperne følger ikke med. Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken. This is a high quality, hand made, dust and water splash proof shroud, designated to fit a particular model. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a break between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good airflow in order to keep the model electronics cool.   Before applying VELCRO® to the chassis, cut the tape to the necessary length and width. For example, to place VELCRO® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width. Make sure that the surface of the chassis is extremely dry and clean before applying the VELCRO® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process). Let the VELCRO® tape adhere to the chassis for 24 hours before you use the shroud. If it?s hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris. When it?s hot outside ? or if you have a car gearing set up that?s capable of reaching the speed of light ? be smart when you bash. Don?t let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature. When bashing in winter, don?t bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics. Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they can?t be breathable and 100 percent waterproof at the same time. Physics just doesn?t work that way. The splashes of water are OK, so don?t be concerned if the shroud gets a bit damp. Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.

DYNS1217 - 88T Motor 180size with Pinion for SCX24 Motor for Axial SCX24, denne gir scx24 bilene bedre dragbrake og regnes som en option. Dynamite® 180-size, 88T Brushed Electric Motor

DYNT0503 - Dynamite SCX24 Verktøysett Startersett med de vanligste verktøy for å reparere-skru på din SCX24 Settet består av : 1 x Hylsenøkkel 4mm for bl.a hjulmutter  1 x Sekskant trekker 0.05" for de minste skruene 1 x Sekskant trekker 1.5mm 1 x Stemplet kulegaffelverktøy med endenøkkel 2-3-4-5mm 1 x Verktøyveske

EC5 Loop Connector (1) Loop kobling for bruk på regulator med seriekabling/kontakt for å bruke 1 batteri. Er kompatibel med iC5 ill foto

ee305 - Spark Plug Cap Tennplugghette fra Zenhoa, passer de fleste bensinmotorer, leveres uten innmat.

ee432 - Rubber Kill Switch Cover

Eksosfjær 1 stk for 3.5-5.9 motorer Fjøra som holder eksosbend mot/rundt motorblokk, universal og passer de fleste 3.5-5.9cc bilmotorer

Eksospakning 3.5-5.9CC 1/8 Svart 5 stk 5 stk silikonpakning for bak eksosmotorer, passer de fleste merker/potter.

ESD Antistatisk Metall Pinsett Sett 6 stk Antistatiske metallpinsetter for Hobbybruk i futteral. Settet består av : 1 stk Rett 1.3 x 98mm (ESD-10) 1 stk Rett 1.3 x 128mm (ESD-11) 1 stk Rett Liten Krok 0.7 x 115mm (ESD-12) 1 stk Rett Rund Flat 3.1 x 112mm (ESD-13) 1 stk Rett Rund Flat 1.6 x 112mm (ESD-14) 1 stk Bøyd Flat 1.0 x 106mm (ESD-15)

FG-01071/02 - Rear stabilizer rod 4mm - female (1p) This item can be assembled on or with the product below : basis kit Evo 2020.1 09504 kit Evo 2020.1 09503 EVO 2020 complete kit 09500 EVO 2020 basic kit 09501

FG-06081 - Steel ball 4x10x15 (4p) Kuler for styrearm FG med 4mm innvendig.

FG-60230 - Front bumper OR (1p) Frontfanger for FG modeller This item can be assembled on or with the product below : BEETLE PRO 4WD 540060 BEETLE PRO 4WD RTR 540060R Fun Cross Sport E RTR + LiPo batteries 670070ERC Monster Truck WB535 4WD clear 24050 Fun Cross Sport 2WD 670070 Fun Cross Sport 2WD RTR 670070R

FG-68253 - Plastic deflection roller 16mm (1p) Støtterulle for belte til FG 4WD

Firma 1/24 Børsteløs Sensor Kombo SCX24 Crawlers INTRODUKSJON Spektrum ™ Firma ™ 1/24th Brushless ESC + Motor Combo er et godt valg for mikro-crawlere og flere som kjører på 2S LiPo-kraft. Den har en magnetisk koder med høy presisjon og rotorposisjonssensor som gir utmerket 1 til 1 kontrollfølelse når du kjører i alle hastigheter og vinkler. Perfekt egnet for stikjøring og fjellcrawlkonkurranser. Dette fremskrittet innen sensorisk motorkontroll gjør at ESC kan matche gassinngangen til motorens turtall med uovertruffen presisjon. Denne kombinasjonen er spesielt designet for Axial ® SCX24 & AX24-plattformen for å gi den ultimate ytelsen for maksimal kraft og realisme. Forhåndsinstallert med 2 mm kulekoblinger for enkel installasjon.   EGENSKAPER Pålitelig 4500Kv sensorert børsteløs motor med utmerket lavhastighetskontroll og jevn drift Drop-in konvertering til alle Axial 1/24th Scale SCX24 & AX24 RTR kjøretøyer. *Merk: Axial SCX24-kjøretøyer utstyrt med HRZ00014 2-i-1-mottaker og HRZ00015-sender krever en SLT3-sender- og mottakeroppgradering for funksjonalitet. Se bruksanvisningen for mer informasjon. (2021 Ford Bronco, Jeep GT Gladiator og Jeep Wrangler vil kreve denne oppgraderingen) Alt inkludert – inkluderer motor, ESC, sensorwire og pinjonggir Crawler-modus: Forover og øyeblikkelig revers med dragbrems 8 Amp (40 Amp Burst) 1-2S kompatibel ESC Kompakt størrelse og klar til installasjon JST PH 2.0-kontakt som passer til Dynamite 7,4V 350mAh 2S Lipo-batteri Slitesterk design og vedlikeholdsfri over børstede motorerOptimalisert for effektivitet og lengre driftstider     DROP-IN OPPGRADERING FOR AXIAL SCX24 & AX24 KJØRETØY Spektrum Firma 1/24-skala sensorert børsteløs motor og ESC gir Axial SCX24 & AX24 entusiast en drop-in motor og ESC-system for å ta crawlingen til neste nivå.     ALT INKLUDERT Systemet inkluderer motor, ESC, sensorwire og piniondrev og er forhåndsinstallert med 2 mm kulekontakter og JST PH 2.0 batterikontakt for å passe til Dynamite 7.4V 350mAh Lipo-batteriet som følger med Axial SCX24 & AX24 kjøretøyene.

Front Drev 10T Stål Promoto MX (1) (LOS262004) Frontdrev for kjededrift foran PM MX

Fuelslange 100cm Silikon 2mm Neon Grønn (1) SPECIFICATIONS Lengde: 1000mm Inner Diameter:  2mm Utvendig Diameter:  5mm Farge : Neon Grønn Silikonslange som kan brukes til de fleste formål. ill.foto

Fuelslange 100cm Silikon 2mm Neon Gul (1) SPECIFICATIONS Lengde: 1000mm Inner Diameter:  2mm Utvendig Diameter:  5mm Farge : Neon Gul Silikonslange som kan brukes til de fleste formål. ill.foto

Fuelslange 100cm Silikon 2mm Neon Rosa (1) SPECIFICATIONS Lengde: 1000mm Inner Diameter:  2mm Utvendig Diameter:  5mm Farge : Neon Rosa Silikonslange som kan brukes til de fleste formål. ill.foto

Fuelslange 100cm Silikon 3.2mm Transparent (1) SPECIFICATIONS Lengde: 1000mm Inner Diameter:  3.2mm Utvendig Diameter: 6.4mm Farge : Transparent/Blank Silikonslange som kan brukes til de fleste formål. ill.foto

Glassfiber Tape 15mm 25m (1) Tape for mange formål, forsterke lexan karosseri, vinger på fly m.m

GTP0113 - Electronic Power Switch In 0-40V (4-8.4V Out) Kan styre alt mulig av elektronikk, lys o.l. fra sender ved å benytte en ledig kanal. Lar deg koble til elektronikk fra 0v til 40v.  Length: 25 mm Width: 10 mm Height: 5 mm Weight: 8 g Power supply control section using the receiver for power: DC 4-8.4V Controlled power supply input section JST Female: DC 0-40V Output JST Male-Charged capacity: 7A maximum, 10A instantaneous

HD Steel Front & Rear Center Shaft for Axial SCX24 C10 og JEEP (133.7mm) Mellomakslinger for SCX24 C10 og Jeep, fremre mellomaksling er lenger på disse.

HD Steel Front & Rear Center Shaft for Axial SCX24 Deadbolt/Betty Mellomakslinger for SCX24 Deadbolt/Betty, fremre mellomaksling er kortere på disse.

High Power Head Light System Meget kraftige super bright LEDs med reflektorer! Bruker 0.5A. Lar seg fjernstyres om man har ledig kanal på mottakeren. Stort bruksområde. Kan for eksempel benyttes i fly, bil og båt.   Features: Power is supplied via the JST-XH balance connector from a 2s lipo battery The JST-XH balance connector input voltage range is 6.5-8.4v DC Control voltage input from the receiver: 5.0V DC Max Specifications: LED Housing Diameter: 22mm LED Housing Depth: 21mm JST-XH (2s) wire length: 180mm Control to LED wire length: 200mm

HPI-104926 - 1966 Ford Mustang GT Coupe 200mm Karosseri Klart uklippet 1/10 200mm lexankarosseri for Touring/Drift HPI Racing er stolte av å introdusere en 200 mm kopi av legendarisk 1966 Ford Mustang GT Coupe! Mustangen er en av de mest kjente tidlige amerikanske Trans-Am-bilene, og er enorm i dragracing-kretser da Ford produserte en bil som kunne gjør alt, noe som gjør Mustang til en amerikansk kultklassiker! Hpi sin naturtro kopi i 1/10-skala fanger opp alle detaljene som gjør Mustang GT Coupe fra 1966 til en favoritt. Dette HPI-fabrikerte karosseriet er designet for å passe perfekt på 200 mm touringbiler. Legg til din egen lakkering, og du er klar til å kjøre race, cruise eller sitte i garasjen klar for concours. Fotorealistiske utstansede premium vinyldekaler inkluderer vindu rammer, frontlykter, baklykter og mer, pluss offisielle logoer! Lyktebrønner foran og bak Oversprayfilm og forhåndskuttede vinylvindusmaskering gjør lakkering raskt og enkelt Et instruksjonsark for klistremerke er inkludert for plassering av klistremerke Karosseriet har fordypningsmerker for plassering av karosseriestolper til Hpi bilene, men kan fint benyttes på andre merker ved å merke seg hvor hull skal være. Støpt av klar polykarbonatplast for holdbarhet og lang liv Dette er en offisielt lisensiert kopi 1/10Touring Car Size 200mm/Use offset wheels for 190mm width chassis Ford Oval and nameplates are registered trademarks owned and licensed by Ford Motor Company. Manufactured by HPI Racing. www.ford.c

HPI-107829 - One way bearing for pullstart 14x6mm Enveislager fra Hpi, denne er identisk med RS12A/13* fra Force This is the One-Way bearing for the HPI Nitro Star engines.                   ** Also fits the Roto Start for the Savage.**             This One-Way Bearing allows the recoil starter to grab the crankshaft to start the engine and spin freely in the opposite direction. THIS PART FITS THE FOLLOWING KITS / PARTS: D8SSTD WR8 3.0 Ford Fiesta Abu Dhabi...STD Trophy Buggy 3.5STD Trophy Truggy 4.6STD NITRO STAR G3.0 HO ENGINE WITH...STD Savage X 4.6STD NITRO STAR F4.6 V2 ENGINE WITH...STD NITRO STAR F3.5 V2 ENGINE WITH...STD KEN BLOCK 2013 GRC WR8 3.0STD WR8 3.0 KEN BLOCK FORD FIESTA ST...STD WR8 3.0 Ken Block 2015 Ford Fiesta...STD NITRO STAR F5.9 ENGINE WITH...STD WR8 3.0 KEN BLOCK GYMKHANA FORD...STD FEATURES: Steel construction INCLUDES: One one-way bearing           One installation instruction sheet REQUIRES: Installing in recoil unit SPECS:    Overall Length:   14mm            Hex Width:        14mm            Inner Diameter:    6mm

HPI-114182 - DSX-2 Truck Painted Body (black/orange) Ferdiglakket og klippet karosseri for bl.a E-Firestorm Flux THIS PART FITS THE FOLLOWING KITS / PARTS: E Firestorm 10t Flux RTRSTD

HPI-1430 - One way bearing for Pullstart 12x6mm Enveislager fra Hpi, denne er identisk med RS12/13 fra Force This is the One-Way bearing for the HPI Nitro Star engines.                   ** Also fits the Roto Start for the Savage.**             This One-Way Bearing allows the recoil starter to grab the crankshaft to start the engine and spin freely in the opposite direction. This Part Fits the following kits / parts: G3.0 ENGINE SLIDE CARB W/PULL... STD NITRO STAR F3.5 ENGINE WITH... STD RTR Bullet ST 3.0 w/ 2.4GHz STD RTR Bullet MT 3.0 w/ 2.4GHz STD NITRO 3 DRIFT RTR WITH DISCOUNT... STD NITRO STAR F4.1 ENGINE WITH... STD NITRO STAR G3.0 ENGINE WITH... STD FEATURES: Steel construction INCLUDES: One one-way bearing           One installation instruction sheet REQUIRES: Installing in recoil unit SPECS:    Overall Length:   12mm (.472")           Hex Width:        12mm (.472")           Inner Diameter:    6mm (.218")

HPI-17519 - 1966 Ford Mustang GT 200mm Karosseri Klart uklippet 1/10 200mm lexankarosseri for Touring/Drift HPI Racing er stolte av å introdusere et 200 mm klart karosseri kopi av den legendariske Ford Mustang Fastback fra 1966! Mustangen er en av de mest kjente tidlige amerikanske Trans-Am-bilene, og en stor tilhengerskare i dragracing-kretser da Ford produserte en bil som kunne gjøre alt, noe som gjør Mustang til en amerikansk kultklassiker! Hpi sin virkelighetstro kopi i 1/10-skala fanger opp alle detaljene som utgjør 1966 Mustang en favoritt. Dette HPI-fabrikerte karosseriet er designet for å passe perfekt på 200 mm touringbiler. Legg til din egen lakkjobb, og du er klar til å kjøre race, cruise eller sitte i garasjen klar for concours. Fotorealistiske utstansede premium vinyldekaler inkluderer vindu rammer, frontlykter, baklykter og mer, pluss offisielle logoer! Oversprayfilm og forhåndskuttede vinylvindusmasker gjør lakkering raskt og enkelt Et instruksjonsark for klistremerke er inkludert for plassering av klistremerke Karosseriet har fordypningsmerker for plassering av karosseriestolper til Hpi bilene, men kan fint benyttes på andre merker ved å merke seg hvor hull skal være. Støpt av klar polykarbonatplast for holdbarhet og lang liv Dette er en offisielt lisensiert kopi 1/10 Touring Car Size/Use 3mm offset wheel for 190mm width chassis. Ford Oval and nameplates are registered trademarks owned and licensed by Ford Motor Company. Manufactured by HPI Racing. www.ford.co

HSP 1/10 Karosseri F-150 260mm WB MT karosseri for 1/10 biler med hjulbase 260mm, karosseriet er ikke hullet så det kan tilpasses flere modeller. Lengde: 430mm Bredde: 182mm Hjulbase : 260mm Leveres i Hvitt, Rødt eller Blått, velges i varianter.

HSP 1/10 MT Karosseri Lakkert 260mm WB MT karosseri for 1/10 biler med hjulbase 260mm, karosseriet er ferdig klippet og hullet. Lengde: 430mm Bredde: 182mm Hjulbase : 260mm

HSP Startboks Black - 1:10 / 1:8 (70109) Startboks for 1:10 og 1:8 Buggy, Truggy og On-roadbiler. Utstyrt med kraftig el-motor som kan drives av 2 x 7.2V batterier eller 12V bilbatteri. Starthjulet er flyttbart i fire ulike posisjoner for passe din modell. Starteren er utstyrt med magnetplate på siden for midlertidig oppbevaring av skruer, plugger e.l. På siden finner du av/på bryter, og den er utstyrt med lufteriller for å gi god kjøling til motor og batterier. Starteren leveres uten batteri og lader. I enden har den et kraftig bærehåndtak for praktisk transport.

HSP-02036 - Front lower shaft 44x3mm, Pin A 2 stk Bærebruaksling Foran, Tyrannosayrus/Warhead/Stormer/Strada MT/XB/EVo,Torche,Booster ++ 1/10

HSP-02053 Karosseriklips 8 stk Karrosseri klips medium sett a 8 stk, passer de fleste 1-18,1-16, 1-12, 1-10, 1-8 samt til de fleste radiobokser. Tynne klips med oppoverbøyd "hode" for maximal fjærstyrke. Lengde: 22,5mm For stolper 0-8mm Godstykkelse: 1,2mm fjærstål

HSP-02101 -  Steering Plate Bushing - 12pcs 4.5x5.3x3.1mm   Produktet er forbundet med:   HSP Kutiger Rally 1:10 Brushed :: Komplett HSP Kutiger Rally 1:10 Brushless :: Komplett HSP Breaker SCT 1:10 Brushed :: Komplett HSP Breaker SCT 1:10 Brushless :: Komplett HSP Breaker Buggy 1:10 Brushless :: Komplett HSP Breaker Buggy 1:10 Brushed :: Komplett

HSP-03601 - Chassis Rally/Brontosaurus 1/10 Chassis for bl.a Kutiger Rally og Brontosaurus

HSP-03610 Battery Cover Batterilås for bl.a HSP, Maverick og Amax/Maxxam biler Lengde : 177mm CC mellom 6.3mm hull 165mm

HSP-06022 - Transmissionshaft/DogBone 87mm(CC-82mm) 2p Drivakslinger totalt 87mm Amax/HSP/WindHobby/Maverick 1/10 elektro Booster, Cheetha mflere.

HSP-08042 - Front/Rear link 3x35mm (2) Styrestag/Øvre lenkearm Brontosaurus/Tribes Head Styrestag 3x35mm + ball ends holder 3x20mm for 4.8mm kule

HSP-108015 - Universal DogBone CVD akslinger (2) Oppgraderingsakslinger for bl. a Brontosaurus fra HSP, erstatter 08029-08059-MV22129-02033

HSP-11164 - 06033 Main Gear 64T 0.6M Spur drev for Wind Hobby, Hsp, Amax, Maverick  1/10 elektro biler 64 tenner, dette er typen med fintanning 0.6M. (Ikke for børsteløs)

HSP-17704 - Shock Absorbers - Blue (2) 2 stk 98mm støtdempere for HSP,Maxam,Right 1/10 Truggy Lengde : 72-98mm Ø : 12mm

HSP-18009 Connect Box W/Main Gear 38T

HSP-20104 Front/Rear Post Mount F/B   Karosserifeste for HSP Breaker 1/10 og Maverick Desert Buggy(MV22723)

HSP-20109 Roll Cage F   Roll Cage for HSP Breaker 1/10 og Maverick Desert Buggy(MV22723)

HSP-20136 Rear Post Mount + Body Post